1、购买一个合适的电动门驱动器。可以根据门的尺寸和重量选择合适的电动驱动器。

　　1. Purchase a suitable electric door driver. Suitable electric drivers can be selected based on the size and weight of the door.

　　2、关闭门，并确保门的运行顺畅。如果门有任何故障或损坏，需要先修复。

　　2. Close the door and ensure its smooth operation. If there is any malfunction or damage to the door, it needs to be repaired first.

　　3、安装电动门驱动器。根据驱动器的安装指南，使用螺丝刀和电钻将驱动器固定在门上。确保驱动器安装稳固。

　　3. Install the electric door driver. According to the installation guide for the driver, use a screwdriver and drill to secure the driver to the door. Ensure that the driver is securely installed.

　　4、连接电动门驱动器的电源。根据驱动器的电气连线图，将电源线与驱动器连接。确保正确连接并固定线路。

　　4. Connect the power supply of the electric door driver. Connect the power cord to the driver according to the electrical wiring diagram of the driver. Ensure proper connection and secure of the circuit.

　　5、连接开关和遥控器。根据驱动器的电气连线图，将开关和遥控器与驱动器连接。确保正确连接并固定线路。

　　5. Connect the switch and remote control. Connect the switch and remote control to the driver according to the electrical wiring diagram of the driver. Ensure proper connection and secure of the circuit.

　　6、进行测试。打开电源，使用开关或遥控器控制门的开闭。确保门能够顺利运行，并检查是否有任何异常。

　　6. Conduct testing. Turn on the power and use a switch or remote control to control the opening and closing of the door. Ensure that the door can operate smoothly and check for any abnormalities.

　　电动卷帘门突然打不开？

　　Electric rolling shutter door suddenly doesn't open?

　　一、卷帘门开启困难，声音刺耳

　　1、 The rolling shutter door is difficult to open and the sound is harsh

　　如果发现通电后卷帘门开启困难并且发出嘈杂声响，那原因极有可能是卷帘门上的帘片被导槽卡住或是帘片变形了。给出的解决办法是，仔细对卷帘门入导槽的槽口处进行查看矫正维修。

　　If it is found that the rolling shutter door is difficult to open and makes a noisy sound after being powered on, the reason is most likely that the curtain on the rolling shutter door is stuck in the guide groove or deformed. The proposed solution is to carefully inspect, correct, and repair the groove at the entrance of the roller shutter door.

　　二、电动机不动或转速慢

　　2、 Electric motor not moving or slow speed

　　此故障原因一般是线路断路、电机烧损、停止按钮没复位、限位开关动作、负载较大等引起。

　　The cause of this fault is generally due to circuit breakage, motor burnout, failure to reset the stop button, limit switch action, high load, etc.

　　处理方法是检查线路、并接通；更换烧损电机；更换按钮或重复按动几次；拨动限位开关滑块使它脱离微动开关触点，并调整微动开关位置；检查机械部分有无卡阻，若出现卡阻则卡阻、清理障碍物。

　　The solution is to check the circuit and connect it; Replace the burnt motor; Replace the button or press it repeatedly a few times; Move the limit switch slider to disengage it from the microswitch contact and adjust the microswitch position; Check if there is any blockage in the mechanical part. If there is any blockage, eliminate it and clean up the obstacles.

　　三、卷帘门不能卷起来，呈圆柱状

　　3、 The rolling shutter door cannot be rolled up and is cylindrical in shape

　　通电之后卷帘门呈圆柱状且不工作，那么可能是内部弹簧折断或是弹簧连接带断裂。出现这种问题就需要更换弹簧吊带。

　　After being powered on, if the rolling shutter door is cylindrical and does not work, it may be due to a broken internal spring or a broken spring connecting strap. If this problem occurs, it is necessary to replace the spring sling.

　　四、卷轴运转困难，开启时感觉阻力

　　4、 The scroll is difficult to operate and feels resistance when opened

　　造成这种故障的原因是因为卷轴两端口的不够润滑，与叶片产生阻力。解决办法是在卷轴两端均匀涂抹润滑油。建议驱动器每年少要加注一次润滑脂，链条应经常加注润滑油，并检查各部件磨损情况，磨损严重的机件要及时维修或更换。

　　The reason for this malfunction is due to insufficient lubrication at the two ports of the spool, which creates resistance with the blades. The solution is to evenly apply lubricating oil on both ends of the scroll. It is recommended to add lubricating grease to the drive at least once a year, regularly lubricate the chain, and check the wear of each component. Parts with severe wear should be repaired or replaced in a timely manner.

　　五、电机振动或噪声较大

　　5、 Motor vibration or noise is high

　　出现这种情况的原因可能有刹车盘不平衡或断裂；刹车盘无紧固；轴承失油或失效；齿轮啮合不顺、失油或磨损严重等这几种故障点。处理方法是更换刹车盘或重新调整平衡；紧固刹车盘螺母；更换轴承；修配电机轴输出端齿轮、润滑或更换；检查电机，如电机坏损则更换。

　　The reason for this situation may be that the brake disc is unbalanced or broken; The brake disc is not securely fastened; Bearing oil loss or failure; There are several fault points such as unsmooth gear meshing, oil loss, or severe wear. The solution is to replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace bearings; Repair, lubricate or replace the gear at the output end of the motor shaft; Check the motor and replace it if it is damaged.

　　六、长期缺少保养引起闸门故障

　　6、 Long term lack of maintenance causes gate failure

　　电动卷帘门的感应探测器探测到有人进入时，就会将脉冲信号传给主控器，主控器判断后通知马达运行，同时监控马达转数，以便通知马达在一定时候加力和进入慢行运行。如果长期缺乏保养，导致电动卷闸门存在的隐患及小故障得不到及时处理，马达得到一定运行电流后做正向运行，将动力传给同步带，再由同步带将动力传给吊具系统使门扇开启；门扇开启后由控制器作出判断，如需关门，通知马达作反向运动，关闭门扇。将会由小故障变成大故障，终可能导致自动电动门的瘫痪，因此定期对电动卷帘门进行保修是非常重要的。

　　When the induction detector of the electric rolling shutter door detects someone entering, it will transmit a pulse signal to the main controller. After judgment, the main controller notifies the motor to run and monitors the motor speed to notify the motor to apply force and enter slow running at a certain time. If there is a long-term lack of maintenance, the hidden dangers and minor faults of the electric roller shutter cannot be dealt with in a timely manner. After the motor receives a certain operating current, it runs forward and transmits power to the synchronous belt, which then transmits power to the lifting system to open the door leaf; After the door leaf is opened, the controller makes a judgment. If the door needs to be closed, it notifies the motor to move in the opposite direction and close the door leaf. It will turn from a minor malfunction to a major one, ultimately leading to the paralysis of the automatic electric door. Therefore, it is very important to regularly provide warranty for the electric rolling shutter door.

　　本文由  济南卷帘门 友情奉献.更多有关的知识请点击  http://www.jnzxmy.com/   真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Jinan Rolling Shutter Doors For more related knowledge, please click http://www.jnzxmy.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.