快速卷帘门的传动机构装置在：门洞的顶盒内。箱体选用22 mm厚镀锌钢板和6 mm厚钢板，端板上配有卷筒轴承、驱动电机、装置座和平衡体系部件的装置孔，钢板表面涂有客户要求的色彩。

The transmission mechanism of the fast rolling shutter door is located inside the top box of the door opening. The box is made of 22mm thick galvanized steel plate and 6mm thick steel plate. The end plate is equipped with device holes for drum bearings, drive motors, device seats, and balance system components. The surface of the steel plate is coated with the color required by the customer.

卷轴装置在机柜内，由卷轴、轴端、轴承座等组成。依据门口的高度和宽度计算出鼓的尺度，挑选合理的尺度。在这个快速卷帘门上，滚筒的直径是219毫米。

The scroll device is located inside the cabinet and consists of a scroll, shaft end, bearing seat, etc. Calculate the scale of the drum based on the height and width of the doorway, and select a reasonable scale. On this fast rolling shutter door, the diameter of the drum is 219 millimeters.

门帘布：门帘布是分段制作的，每段高度约为两边700mm。每段窗帘布经过特制的铝抗风条连接成一个整体的窗帘布，窗帘布的厚度为1。 2mm，具有强度高、耐冲击、不易刺穿的优点。也能够挑选=2mm的通明PVC原料的窗帘布或许组件为通明PVC原料，观察快速卷帘门两边的状况。帘布底部设有铝底梁，防撞软袋帘布顶部用螺丝和压条固定在卷筒上。

Door curtain fabric: The door curtain fabric is made in sections, with each section height of approximately 700mm on both sides. Each section of the curtain fabric is connected into a single unit by a specially designed aluminum wind resistant strip, with a thickness of 1. 2mm, with the advantages of high strength, impact resistance, and not easy to puncture. It is also possible to select curtain fabrics made of 2mm transparent PVC material or components made of transparent PVC material, and observe the condition on both sides of the quick rolling shutter door. The bottom of the curtain is equipped with an aluminum bottom beam, and the top of the anti-collision soft bag curtain is fixed to the drum with screws and pressure strips.

驱动设备：快速卷帘门的转轴由减速电机直接驱动。依据升降速度的要求，挑选不同速比的减速机达到所需的升降速度，Z向速度可达80 cm/s以上，操控线选用变频操控，使帘布在运转中缓慢启停，帘布在运转中停止移动。

Driving equipment: The shaft of the fast rolling shutter door is directly driven by a deceleration motor. According to the requirements of lifting speed, select reducers with different speed ratios to achieve the required lifting speed. The Z-direction speed can reach 80 cm/s or above. The control line adopts variable frequency control to slowly start and stop the fabric during operation, and the fabric stops moving during operation.

导槽箱：导槽箱2厚2厚mm镀锌钢板制成，固定在门洞两边的墙上，机箱放置在导槽箱顶部，经过螺栓固定在导槽箱和墙上。导槽箱的导槽两边固定有密封条，以证一定的密封要求，导槽箱底部离地约1m假如位置较高，则保留红外监视器的装置位置。

Guide box: The guide box is made of 2mm thick galvanized steel plate and fixed on the walls on both sides of the door opening. The chassis is placed on the top of the guide box and fixed to the guide box and wall with bolts. There are sealing strips fixed on both sides of the guide groove of the guide groove box to meet certain sealing requirements. If the bottom of the guide groove box is about 1m above the ground, the position of the infrared monitor device should be retained.