卷帘门故障处理

　　Troubleshooting of rolling shutter doors

　　底盘区域后桥线及托盘库有四个EFAFLEX（艾富来）卷帘门，在区域断电后会出现卷帘门故障无法升降的问题，需要对卷帘门进行限位初始化，下面是具体操作步骤。

　　There are four EFAFLEX rolling shutter doors on the rear axle line and pallet warehouse in the chassis area. After a power outage in the area, there may be a problem of the rolling shutter doors malfunctioning and unable to lift. It is necessary to initialize the limit of the rolling shutter doors. The following are the specific steps for operation.

　　后桥线体突然断电后VH01工位卷帘门故障处理2025.10.27故障现象:后桥线PLC断电后1工位料库卷帘门报警终端不一致故障，无法对面板送自动

　　Fault handling of VH01 station rolling shutter door after sudden power failure of the rear axle line body on May 27, 2023 Fault phenomenon: After the PLC of the rear axle line was powered off, the rolling shutter door alarm of station 1 material warehouse was inconsistent with the safety terminal, and the panel could not be automatically sent

　　处理过程:1、如果卷帘门能够自动找到上下限位，那么直接操作上下及STOP按钮操作即可。具体操作步骤:

　　Process: 1. If the rolling shutter door can automatically find the upper and lower limits, then simply operate the up and down buttons and the STOP button. Specific operating steps:

　　1当看到卷帘门控制器报警0一_To Begin后点击操作面板的向下按钮，是卷帘门的下到我开关与立柱的下到位开关对齐保证有信号

　　When you see the alarm of the rolling shutter door controller 0-To Begin, click the down button on the operation panel to align the down to me switch of the rolling shutter door with the down to position switch of the column to ensure there is a signal

　　2然后长按STOP按钮，此时卷帘门将自动上升打开卷帘门，这个时候不需要任何操作，卷帘门开始自己找位置，时间约1分钟左右，如果正常上升到卷

　　2. Then press and hold the STOP button. At this point, the rolling shutter door will automatically rise and open. No operation is required at this time. The rolling shutter door will start to find its position on its own, taking about 1 minute. If it rises normally, it will roll

　　帘门的上限位，那么恢复正常。如果连续撞击上限位，那么就需要按照下一页的PPT方法进行操作了。

　　The upper limit of the curtain door should be restored to normal. If there is a continuous impact on the upper limit, then it is necessary to follow the PPT method on the next page for operation.

　　底盘区域后桥线及托盘库有四个EFAFLEX（艾富来）卷帘门，在区域断电后会出现卷帘门故障无法升降的问题，需要对卷帘门进行限位初始化，下面是具体操作步骤。

　　There are four EFAFLEX rolling shutter doors on the rear axle line and pallet warehouse in the chassis area. After a power outage in the area, there may be a problem of the rolling shutter doors malfunctioning and unable to lift. It is necessary to initialize the limit of the rolling shutter doors. The following are the specific steps for operation.

　　后桥线体突然断电后VH01工位卷帘门故障处理

　　Fault handling of VH01 station rolling shutter door after sudden power failure of rear axle line body

　　1.上键和停止键同时按住3秒进入调试界面-P.000-运行次数

　　1. Press and hold the up and stop keys simultaneously for 3 seconds to enter the debugging interface - P.000- run times

　　2.点动按上键(多次)-直到出现-P.999-此时-P.999下方有光标闪动

　　2. Tap and press the up key (multiple times) - until - P.999 appears - at this point, the cursor flashes below - P.999

　　3.点动按停止键使光标移动到右侧--00000下方有光标闪动

　　3. Tap and press the stop button to move the cursor to the right - there is a flashing cursor below 00000

　　4.点动按上键14次--直到出现--0000E

　　4. Tap and press the up key 14 times until --0000E appears

　　5.按住停止键3秒--直到0000E的右侧 直到出现钩号(确认)

　　5. Press and hold the stop button for 3 seconds - until a hook appears on the right side of 0000E (confirm)

　　6.再次点动按停止键一使光标移动到左侧

　　6. Press and hold the stop button again to move the cursor to the left

　　7.点动按下键(许多次)直到--P.210-0

　　7. Tap and press the key (many times) until -- P.210-0

　　8.点动按停止键使光标移动到右侧

　　8. Press and hold the stop key to move the cursor to the right

　　9.P.210--0调整为P.210-5按住停止键3秒直到出现(钩号)(确认)

　　9. Adjust P.210-0 to P.210-5. Press and hold the stop button for 3 seconds until a hook appears (confirm)

　　10.点动按停止键使光标移动到左侧

　　10. Tap and press the stop button to move the cursor to the left

　　11.按住停止键3秒退出调试界面

　　11. Press and hold the stop button for 3 seconds to exit the debugging interface

　　12.此刻按下键 门会下降按上键门会上升

　　12. Pressing the key at this moment will cause the door to descend, while pressing the key will cause the door to ascend

　　13.选择快速门关闭到位的位置(门关闭的合适位置)

　　13. Choose the position where the quick door closes properly (the appropriate position for door closure)

　　14.按住停止键3秒系统自动保存位置

　　14. Press and hold the stop button for 3 seconds, and the system will automatically save the location

　　15.此刻快速门会自动运行几分钟(不要触动任何按钮)

　　At this moment, the fast door will automatically run for a few minutes (do not touch any buttons)

　　16.期间如有故障，显示屏会有提示

　　If there is a malfunction during the period, the display screen will show a prompt

　　17.出现10秒关闭快速门完成重置

　　17. A countdown of 10 seconds occurs, and the quick door is closed to complete the reset

　　底盘区域后桥线及托盘库有四个EFAFLEX（艾富来）卷帘门，在区域断电后会出现卷帘门故障无法升降的问题，需要对卷帘门进行限位初始化，下面是具体操作步骤。

　　There are four EFAFLEX rolling shutter doors on the rear axle line and pallet warehouse in the chassis area. After a power outage in the area, there may be a problem of the rolling shutter doors malfunctioning and unable to lift. It is necessary to initialize the limit of the rolling shutter doors. The following are the specific steps for operation.

　　底盘区域后桥线及托盘库有四个EFAFLEX（艾富来）卷帘门，在区域断电后会出现卷帘门故障无法升降的问题，需要对卷帘门进行限位初始化，下面是具体操作步骤。

　　There are four EFAFLEX rolling shutter doors on the rear axle line and pallet warehouse in the chassis area. After a power outage in the area, there may be a problem of the rolling shutter doors malfunctioning and unable to lift. It is necessary to initialize the limit of the rolling shutter doors. The following are the specific steps for operation.

　　如果有许多参数都错误了，那么就需要设备初始化，然后按照上述参数一个一个修改，然后再重新适配卷帘门的上下限位

　　If many parameters are incorrect, the device needs to be initialized, and then modified one by one according to the above parameters, and then re adapted to the upper and lower limits of the rolling shutter door